HP Color LaserJet 2500L Printer Q9705A

Status: Available
Condition: OEM

Your Price: RFQ

Printer Parts
Printer Information
Related Models

Airflow Guide

RB2-9904-000CN - Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right side

RB3-0025-000CN - Airflow guide (duct) / fan holder bracket assembly (Quartz Gray plastic)

RB3-0089-030CN - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open

RB3-0063-000CN - Paper feed belt - Small black rubber belt approximately 1/8 inch wide with little 'A' shaped ribs on it

RB1-8668-030CN - Feed guide drive belt - Small belt approximately 5/16 inch wide with 'A' shaped ribs on it

RB1-8668-000CN - Feed Guide Drive Belt

Bezel

RB3-0035-000CN - Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors

Bushing

RB2-2973-000CN - Support bushing

RB2-3043-000CN - Left roller bushing - Acts as the bearing and retainer for the left end of the paper pickup roller assembly (tray 1)

RB2-3044-000CN - Right roller bushing - Acts as the bearing and retainer for the right end of the paper pickup roller assembly (tray 1)

RB2-9808-000CN - Bushing/shaft retainer assembly - Black plastic

RB2-9809-000CN - Bushing/shaft retainer assembly (White plastic)

RB3-0014-000CN - Bushing assembly (black plastic bushing with small guide roller on top)

RS5-1635-000CN - Shaft bushing for HP Color LaserJet 1500 Series

RS5-1637-000CN - Bushing (black plastic)

RS5-1638-000CN - Bushing for HP Color LaserJet 1500 Series

Cable

C2951A - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long

C9706-60104 - Flat flexible cable

RG5-6974-000CN - Cable assembly for HP Color LaserJet 1500 Series

RG5-7130-000CN - High voltage cable assembly

RG5-7108-000CN - Cable assembly (two 8-pin connectors, Purple wire)

RG5-7109-000CN - Cable assembly (two 7-pin connectors)

RG5-7115-000CN - Cable assembly (two 3-pin connectors)

RG5-7128-000CN - Cable assembly (four 3-pin connectors)

RG5-7129-000CN - Cable assembly (two connectors and two spade lugs)

RG5-7106-000CN - Cable assembly (two 2-pin connectors)

RG5-7146-000CN - High voltage cable assembly (two 15-pin connectors and two 14-pin connectors)

RG5-7107-000CN - Cable assembly (8-pin, red wire)

RG5-7117-000CN - Cable assembly (two 3-pin connectors)

RG5-7122-000CN - Cable assembly - 'Y' type cable (three connectors) - The 14-pin connector splits into an 8-pin connector and a 6-pin connector

RG5-7123-000CN - Grounding cable assembly

RG5-7126-000CN - Cable assembly (two 5-pin connectors)

RG5-7144-000CN - Cable assembly (with seven connectors)

RG5-7145-000CN - Front cable assembly (six connectors)

RG5-7161-000CN - Cable assembly (two 3-pin connectors and a spad lug)

RH2-5524-000CN - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101)

RG5-7114-020CN - Cable assembly (two 4-pin connectors) with shield - Connects between the cartridge drive motor and the DC controller board

5063-1256 - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long

5063-1257 - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 3.0m (9.8ft) long

Carousel

RG5-6910-080CN - Carousel (Rotary) assembly - Includes the carousel assembly, the support assembly, end plates, drive gears and shaft, sensors, and cables

Cleaner

5090-3379 - Toner cleaning cloth - Specially treated cloth for absorbing toner or Ink (1 per package) - Ideal for cleaning up toner spills and Ink for your plotter / copier / printer

WT2-5056-000CN - Cable clip - `C` shaped White plastic

XD2-1100-502CN - E-ring clip for HP Color LaserJet 1500 Series

Clutch

RH7-5389-000CN - Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft

Connector

RH2-5520-000CN - Connector for the fusing assembly - Seven small contol pins plus three separated high current pins

WS1-6336-000CN - Connector assembly - For optional bottom paper tray

Control Panel

RG5-6927-000CN - Control panel assembly (mechanical only) - Includes the 'Rotate Carousel', 'Cancel Job' and the 'Go' buttons, plus the various indicator light pipes - All switches and LED's are on the formatter PC board

Cover

RB3-0028-000CN - Left side cover (Quartz Gray) - Does not include any attaching parts

RB3-0052-000CN - Gear Cover (Small Black plastic cover) - Covers the left end of the feed drive shaft

RB3-0030-000CN - Upper rear cover (Quartz Gray) - Mounts on the upper rear of the printer above the face-up output tray door

RB3-0032-000CN - Face-down paper output L-Shaped cover ( Blue) - Serves as the rear of the tray for the face-down output tray on top of the printer

RB3-0102-000CN - Front inner cover (Blue) - Mounts on the front frame above the multi-purpose input tray

RB3-0103-000CN - Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the printer logo

RB3-0104-000CN - Roller cover - Covers the multipurpose paper pickup roller assembly - Mounts on the lower front of the front frame assembly

RG5-6900-000CN - Top cover assembly (blue plastic) - Includes the molded-in face-down output tray and the lift-up top cover door assembly

RG5-6902-000CN - Left side cover assembly (Quartz Gray) plastic - Includes the power switch button, rod and spring (The power switch is located on the low voltage power supply board)

RG5-6953-000CN - Right side cover assembly (Quartz Gray) plastic - Includes the DIMM memory door

RB2-9916-020CN - Cover - For the engaging motor (PM704) - Mounts on the upper left side of the rear frame assembly

RB3-0120-020CN - Solenoid cover (Steel) - For magnetic wave sheilding - Mounts over the solenoid on the right side of the front frame assembly

Damper

RB2-6248-000CN - Damper assembly (Gray plastic piece with small 13-tooth gear on it)

RB3-0033-000CN - Memory access door (Quartz Gray perforated plastic) - Allows access to the printer memory slots - Mounts on the right side cover

RF5-4007-000CN - Top cover door (blue plastic) - For accessing the toner cartridges and the imaging drum/transfer assembly - Mounts to the top cover frame

Drive Assembly

RG5-6911-000CN - Rotary drive assembly - Includes the carousel rotating motor (DCM703), toner cartridge drive motor (PM705), developing rotary stopper solenoid (SL93), bracket, and gears

RH7-1630-000CN - Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA)

RB2-9925-000CN - Sensor arm and flag - Activates the photosensor (Does NOT include the roller)

RB3-0111-000CN - Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other

RB3-0135-000CN - Test print flag (Black lever)

RB2-6297-000CN - Rubber foot - Square self-adhesive rubber foot

Fuser Assembly

RG5-6903-000CN - Fuser Assembly (For 110V to 127V operation) - Bonds the toner to the paper with heat

RM1-3525-000CN - Fusing assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat - Slides in and locks in lower rear of printer

RB3-0022-000CN - 22 tooth gear (Black plastic) - Small gear with diagonally cut teeth

RB3-0091-000CN - 16 tooth gear (Black plastic) - Gear with large stop tooth and shaft lock tab

RB3-0092-000CN - 15 tooth gear with drive shaft (Black plastic)

RS7-0418-000CN - 26 tooth gear (Black plastic) - Has 1/8th portion of gear cut away

RS7-0424-000CN - Dual gear - 20 tooth / 40 tooth

RS7-0425-000CN - 30 tooth gear (White plastic)

RS7-0426-000CN - Dual gear - 26 tooth / 50 tooth (White plastic)

RS7-0428-000CN - 30 tooth gear (White plastic)

RS7-0429-000CN - 26 tooth gear (White plastic) - Has recess for shaft drive pin

RS7-0435-000CN - Dual gear - 32 tooth / 37 tooth (White plastic)

RS7-0436-000CN - Dual gear - 37 tooth / 43 tooth (White plastic)

RS7-0437-000CN - 51 tooth gear (White plastic)

Gear Assembly

RG5-6938-030CN - Gear assembly - Metal plate with two White plastic gears attached

Ground

RB2-9942-000CN - Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards

RB3-0119-000CN - Grounding plate

Guide

RB2-9903-000CN - Cable guide (Quartz Gray plastic)

RB2-9912-000CN - Top output bin guide - Small curved ribbed black plastic piece

RB2-9954-000CN - Left paper feed guide (small Black plastic arm)

RB2-9955-000CN - Right paper feed guide (small Black plastic arm)

RF5-4049-000CN - Entrance guide assembly - Angled metal guide between the registration roller and the transfer roller

RG5-6935-020CN - Left cartridge guide assembly

RG5-6929-000CN - Separation guide assembly - Includes the plastic guide, label, and the two small spring loaded rollers

RG5-6930-000CN - Lower separation guide assembly - Includes the guide bracket, paper output sensor (PS1) and flag, exit drive shaft with two rubber rollers, shaft gear, and idler gear

RG5-6951-000CN - Paper guide assembly - Paper width adjustable guide assembly for the multi-purpose front input tray (tray 1)

Hinge

RB2-6405-000CN - Tray hinge - For the left side of the multi-purpose front input tray (Tray 1)

RB2-6406-000CN - Tray hinge - For the right side of the multi-purpose front input tray (Tray 1)

Holder

RB2-9924-000CN - Sensor assembly mounting holder

RB3-0006-000CN - Holder - Housing for the fusing connector assembly

RB3-0023-000CN - Interlock switch holder (Quartz Gray plastic) - Does NOT include the micro-switch

Insulator

RB3-0007-000CN - Insulating sheet (Transparent plastic)

RB3-0056-000CN - Insulating sheet (Transparent plastic)

Label

RS6-8662-000CN - Label for Color LaserJet 2500 Series, Color LaserJet 1500 Series, Color LaserJet 2550 Series

Laser Scanner

RG5-6890-030CN - Laser/scanner assembly

Lever

RB3-0178-000CN - Right side lock release lever

RB3-0179-000CN - Left side lock release lever

Memory

Q7708AX - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package

Q7709AX - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM

Q7707AX - 32MB, 100-pin SDRAM DIMM memory module

Motor

RF5-4010-020CN - Main motor assembly - Large motor mounted on a controller PC board - Mounts on the inside of the metal right side frame assembly

RG5-6958-000CN - Rotary motor assembly

RH7-1625-000CN - Stepping motor - 24VDC

RH7-1629-000CN - Stepping motor - 24V DC

RB2-9960-000CN - Separation pad assembly - Includes the gray plastic frame with the rubber insert strip - For the cassette on the 250-sheet and 500-sheet input tray assemblies - Mounts in the paper cassette tray assembly Replaced by RF5-4258-020CN

RF5-4012-000CN - Separation pad assembly - Includes the separation pad, holder and spring

RF5-4047-000CN - Light blocking pad assembly - Black plastic frame with soft rubber gasket and stiff conductive Mylar piece (grounded)

Paper

Q1298A - LaserJet Satin finish tough paper - A size (8.5 x 11-inches) - Will not tear and will withstand outdoor weather conditions - Can print on both sides

Q1298B - LaserJet Satin finish tough paper - A4 size (21.0cm x 29.7cm) - Will not tear and will withstand outdoor weather conditions - Can print on both sides - 50 sheets per box

PC Board

C9145-69001 - Formatter board assembly - Includes the formatter board and all the metal cage covers

C9705-69003 - DC controller board - Mounts on the left side of the printer (Behind the formatter board assembly)

RG5-6965-000CN - Waste toner sensor PC board - Small board with an LED and photoelectric sensor - Monitors the level of the excess toner deposited in the imaging drum/transfer assembly

RG5-7613-000CN - Registration sensor PC Board - Small board with flag activated photosensor

RG5-7609-000CN - Carousel position and toner level photoelectric sensor PC board - `L` Shaped PC board with the two sensors

RG5-7612-000CN - Top of page photoelectric sensor PC board - Includes the photoelectric top of page sensor and the print engine test switch

RH7-7158-000CN - Density photoelectric sensor PC board

WG8-5593-000CN - Sensor PC board - Small board with flag activated photosensor

WG8-5836-000CN - PHOTOINTERRUPTER Stapler Stacker

Plate

RB3-0057-000CN - Transfer slide plate - Small 'U' shaped metal insert plates

RB3-0065-000CN - Contact plate - copper clad metal spring - Holds the left end of the small 500 Meg-ohm resistor

RB3-0066-000CN - Contact plate - copper clad metal spring - Holds the right end of the small 500 Meg-ohm resistor

RB3-0286-000CN - Contact plate for HP Color LaserJet 2500 Seriess

RB3-0010-030CN - Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through

Power Cord

8120-6800 - Power cord (Flint Gray) - 3-wire, 16 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 240V in Israel)

8120-6809 - Power cord (Dove Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in the U.K., Hong Kong, Singapore, Malaysia)

8120-6811 - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi Arabia, South Africa, India, and Korea)

8120-6812 - Power cord (Flint Gray) - 18 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 120VAC in the United States, Canada, Mexico, Philippines, and Taiwan)

8120-6813 - Power cord (Dove Gray) - Three Conductor, 2.3M (7.5ft) long - Has straight (F) C13 receptacle (For 240VAC in the United Kingdom, Hong Kong, Singapore, Malaysia)

8120-6814 - Power cord (Flint Gray) - 17 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 220VAC in Denmark)

8120-6815 - Power cord (Flint Gray) - 17 AWG, three conductor, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 220VAC in Switzerland)

Power Supply

RG5-6960-000CN - High voltage power supply board (HVT) assembly - Has contacts for the eight high voltage springs in the printer

RG5-7616-000CN - Sub-high voltage board - Small auxillary PC board

RH3-2241-000CN - Low voltage power supply - For 110V to 127V AC operation - Includes the AC power input connector and power switch

RH3-2243-000CN - Low voltage power supply - For 220V to 240V AC operation - Includes the AC power input connector and power switch

Pressure Assembly

RG5-6943-020CN - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft - Primary support structure for the toner cartridge carousel

Pulley

RB3-0061-000CN - Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1-3/4 inches) long with three ball type pulleys

RB3-0067-000CN - Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (5/8 inch) long with one ball type pulley

Rack Slide

RB3-0090-000CN - Rack slide - White plastic piece with gear teeth layed out in rack form on both sides

Reader

RG5-7131-000CN - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board

RG5-7132-000CN - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board

RB3-0037-000CN - Power switch rod - Goes between the power button and the power switch on the low voltage power supply board

Roller

RB2-7195-000CN - Sensor flag roller (small White plastic roller)

RB2-9908-000CN - Pressure roller (small Black hard plastic disk shaped roller)

RB2-9909-000CN - Pressure roller (small Black hard plastic 'solid' roller)

RB3-0012-000CN - Belt roller - Small oval shaped roller approximately 1-3/4 inches long

RB3-0160-000CN - Paper pickup roller ('D' shaped)

RF5-4040-020CN - Transfer roller assembly - Long black foam type roller - Transfers static charge to paper Part RF5-4040-000CN is no longer supplied. Please order the replacement, RF5-4040-020CN

RG5-6897-020CN - Upper top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, two anti-reversing flaps, and the drive gear

RG5-6936-000CN - Lower top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, and the drive gear

RG5-6939-020CN - Registration roller assembly - Includes the roller, bushings, mounting plate, paper sensor, and the sensor flag

RG5-6952-020CN - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1) - Mounts in the lower portion of the front frame assembly

Shaft

RB2-4933-000CN - Lock release shaft - Small shaft with locking tab - Does NOT include the lock release lever

RB3-0011-000CN - Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley

RB3-0060-020CN - Idler gear shaft - Short metal rod

Shield

RB2-9932-000CN - RFI shield - Parallel wire form mounted over the fan

Shutter

RG5-6940-050CN - Registration shutter assembly - Includes the metal roller, mounting frame, grounding springs, and the dual coupling gear

Sideplate

RG5-6932-070CN - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) - Mounts on the right side

RG5-6934-000CN - Right rear side plate assembly - Includes the rear half of the metal right side plate, the fusing assembly drive motor and the three associated gears

RG5-6942-030CN - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges - Mounts on the metal carousel support frame

Solenoid

RH7-5337-000CN - Solenoid assembly

RH7-5384-000CN - Solenoid assembly

Spring

RB2-9905-000CN - Torsion spring for HP Color LaserJet 2500 Series

RB2-9906-000CN - Torsion spring for HP Color LaserJet 1500 Series

RB2-9952-000CN - Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag

RB3-0015-000CN - Compression spring

RB3-0016-000CN - Electrical contact spring - Spring steel wire with compression springs formed on both ends

RB3-0042-000CN - Electrical contact spring

RB3-0043-000CN - Electrical contact spring

RB3-0044-000CN - Electrical contact spring

RB3-0045-000CN - Electrical contact spring

RB3-0046-000CN - Electrical contact spring

RB3-0047-000CN - Electrical contact spring

RB3-0048-000CN - Electrical contact spring

RB3-0121-000CN - Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer

RB3-0122-000CN - Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer

RS6-2030-000CN - Tension spring for HP Color LaserJet 1500 Series

RS6-2759-000CN - Compression spring

RS6-2766-000CN - Tension spring for HP Color LaserJet 1500 Series

Static Dissipater

RB3-0009-000CN - Static eliminator ground plate - Right angled metal piece with small teeth on top edge

Support

RB3-0062-000CN - PC board support (Black plastic holder)

RG5-6907-030CN - Laser/scanner support assembly (sheet metal plate)

Switch

RH7-6051-000CN - Microswitch with lever activator

Thermistor

RH7-7159-000CN - Thermistor for HP Color LaserJet 2820 Series

RB3-0019-000CN - Toner catch tray (curved Black plastic piece) - Holds residual toner from photosensitive drum

RB3-0176-000CN - Face-Up output tray door (ONLY)

RG5-6931-000CN - Face-up output tray assembly - Includes the pull-down door and fusing assembly locking bracket (Does NOT include the lock releases)

Tray Assembly

C9698A - Optional 250 sheet paper input tray - Includes tray base which attaches to printer, and the slide out paper tray - Accommodates 148mm x 210mm (5.8 x 8.3 inches) to 216mm x 356mm (8.5 x 14 inches) media - Only one 250 sheet tray supported per printer

C9699A - Optional 500 sheet paper input tray - Includes tray base which attaches to tray 2, and the slide out paper tray - Accommodates 216mm x 279mm (8.5 x 11 inches) or 210mm x 279mm (8.3 x 11.7 inches) media - Optional 250 sheet tray must be installed first

RG5-6937-000CN - Multi-purpose front input tray assembly (tray-1) - Includes the front cover piece, pull-out paper support, and the flip-out extender

HP Color LaserJet 2500L Printer

Manufacture:

HP

MPN: Q9705A
Description:

HP Color LaserJet 2500L Printer

Condition: OEM
Warranty: 1 year warranty with OEM supplies from the manufacture.
Product Options:

OEM is not available
Refurbished is not available

Image/s:

All Images are subject to correction, more than one part number may share the same image.

Product Tags: Q9705A Color Laser Q9705A CB506-67901

C9693A HP Color LaserJet 2500lse printer

HP
HP Color LaserJet 2500lse printer
C9693A

HP
HP Color LaserJet 2500L Printer
C9705A

HP
HP Color LaserJet 2500 Printer
C9706A

HP
HP Color LaserJet 2500N Printer
C9707A

HP
HP Color LaserJet 2500tn Printer
C9708A